Overview
This section introduces raid.py, a simple RAID simulator you can use to shore
up your knowledge of how RAID systems work. It has a number of options, as we
see below:
prompt> ./raid.py -h
Usage: raid.py [options]
Options:
-h, --help show this help message and exit
-s SEED, --seed=SEED the random seed
-D NUMDISKS, --numDisks=NUMDISKS
number of disks in RAID
-C CHUNKSIZE, --chunkSize=CHUNKSIZE
chunk size of the RAID
-n NUMREQUESTS, --numRequests=NUMREQUESTS
number of requests to simulate
-S SIZE, --reqSize=SIZE
size of requests
-W WORKLOAD, --workload=WORKLOAD
either "rand" or "seq" workloads
-w WRITEFRAC, --writeFrac=WRITEFRAC
write fraction (100->all writes, 0->all reads)
-R RANGE, --randRange=RANGE
range of requests (when using "rand" workload)
-L LEVEL, --level=LEVEL
RAID level (0, 1, 4, 5)
-5 RAID5TYPE, --raid5=RAID5TYPE
RAID-5 left-symmetric "LS" or left-asym "LA"
-r, --reverse instead of showing logical ops, show physical
-t, --timing use timing mode, instead of mapping mode
-c, --compute compute answers for me
In its basic mode, you can use it to understand how the different RAID levels
map logical blocks to underlying disks and offsets. For example, let's say we
wish to see how a simple striping RAID (RAID-0) with four disks does this
mapping.
prompt> ./raid.py -n 5 -L 0 -R 20
...
LOGICAL READ from addr:16 size:4096
Physical reads/writes?
LOGICAL READ from addr:8 size:4096
Physical reads/writes?
LOGICAL READ from addr:10 size:4096
Physical reads/writes?
LOGICAL READ from addr:15 size:4096
Physical reads/writes?
LOGICAL READ from addr:9 size:4096
Physical reads/writes?
In this example, we simulate five requests (-n 5), specifying RAID level zero
(-L 0), and restrict the range of random requests to just the first twenty
blocks of the RAID (-R 20). The result is a series of random reads to the
first twenty blocks of the RAID; the simulator then asks you to guess which
underlying disks/offsets were accessed to service the request, for each
logical read.
In this case, calculating the answers is easy: in RAID-0, recall that the
underlying disk and offset that services a request is calculated via modulo
arithmetic:
disk = address % number_of_disks
offset = address / number_of_disks
Thus, the first request to 16 should be serviced by disk 0, at offset 4. And
so forth. You can, as usual see the answers (once you've computed them!), by
using the handy "-c" flag to compute the results.
prompt> ./raid.py -R 20 -n 5 -L 0 -c
...
LOGICAL READ from addr:16 size:4096
read [disk 0, offset 4]
LOGICAL READ from addr:8 size:4096
read [disk 0, offset 2]
LOGICAL READ from addr:10 size:4096
read [disk 2, offset 2]
LOGICAL READ from addr:15 size:4096
read [disk 3, offset 3]
LOGICAL READ from addr:9 size:4096
read [disk 1, offset 2]
Because we like to have fun, you can also do this problem in reverse, with the
"-r" flag. Running the simulator this way shows you the low-level disk reads
and writes, and asks you to reverse engineer which logical request must have
been given to the RAID:
prompt> ./raid.py -R 20 -n 5 -L 0 -r
...
LOGICAL OPERATION is ?
read [disk 0, offset 4]
LOGICAL OPERATION is ?
read [disk 0, offset 2]
LOGICAL OPERATION is ?
read [disk 2, offset 2]
LOGICAL OPERATION is ?
read [disk 3, offset 3]
LOGICAL OPERATION is ?
read [disk 1, offset 2]
You can again use -c to show the answers. To get more variety, a
different random seed (-s) can be given.
Even further variety is available by examining different RAID levels.
In the simulator, RAID-0 (block striping), RAID-1 (mirroring), RAID-4
(block-striping plus a single parity disk), and RAID-5 (block-striping with
rotating parity) are supported.
In this next example, we show how to run the simulator in mirrored mode. We
show the answers to save space:
prompt> ./raid.py -R 20 -n 5 -L 1 -c
...
LOGICAL READ from addr:16 size:4096
read [disk 0, offset 8]
LOGICAL READ from addr:8 size:4096
read [disk 0, offset 4]
LOGICAL READ from addr:10 size:4096
read [disk 1, offset 5]
LOGICAL READ from addr:15 size:4096
read [disk 3, offset 7]
LOGICAL READ from addr:9 size:4096
read [disk 2, offset 4]
You might notice a few things about this example. First, the mirrored
RAID-1 assumes a striped layout (which some might call RAID-10, or
stripe of mirrors), where logical block 0 is mapped to the 0th block
of disks 0 and 1, logical block 1 is mapped to the 0th blocks of disks
2 and 3, and so forth (in this four-disk example). Second, when
reading a single block from a mirrored RAID system, the RAID has a
choice of which of two blocks to read. In this simulator, we use a
relatively silly way: for even-numbered logical blocks, the RAID
chooses the even-numbered disk in the pair; the odd disk is used for
odd-numbered logical blocks. This is done to make the results of each
run easy to guess for you (instead of, for example, a random choice).
We can also explore how writes behave (instead of just reads) with the -w
flag, which specifies the "write fraction" of a workload, i.e., the fraction
of requests that are writes. By default, it is set to zero, and thus the
examples so far were 100\% reads. Let's see what happens to our mirrored RAID
when some writes are introduced:
prompt> ./raid.py -R 20 -n 5 -L 1 -w 100 -c
...
LOGICAL WRITE to addr:16 size:4096
write [disk 0, offset 8] write [disk 1, offset 8]
LOGICAL WRITE to addr:8 size:4096
write [disk 0, offset 4] write [disk 1, offset 4]
LOGICAL WRITE to addr:10 size:4096
write [disk 0, offset 5] write [disk 1, offset 5]
LOGICAL WRITE to addr:15 size:4096
write [disk 2, offset 7] write [disk 3, offset 7]
LOGICAL WRITE to addr:9 size:4096
write [disk 2, offset 4] write [disk 3, offset 4]
With writes, instead of generating just a single low-level disk operation, the
RAID must of course update both disks, and hence two writes are issued.
Even more interesting things happen with RAID-4 and RAID-5, as you might
guess; we'll leave the exploration of such things to you in the questions
below.
The remaining options are discovered via the help flag. They are:
Options:
-h, --help show this help message and exit
-s SEED, --seed=SEED the random seed
-D NUMDISKS, --numDisks=NUMDISKS
number of disks in RAID
-C CHUNKSIZE, --chunkSize=CHUNKSIZE
chunk size of the RAID
-n NUMREQUESTS, --numRequests=NUMREQUESTS
number of requests to simulate
-S SIZE, --reqSize=SIZE
size of requests
-W WORKLOAD, --workload=WORKLOAD
either "rand" or "seq" workloads
-w WRITEFRAC, --writeFrac=WRITEFRAC
write fraction (100->all writes, 0->all reads)
-R RANGE, --randRange=RANGE
range of requests (when using "rand" workload)
-L LEVEL, --level=LEVEL
RAID level (0, 1, 4, 5)
-5 RAID5TYPE, --raid5=RAID5TYPE
RAID-5 left-symmetric "LS" or left-asym "LA"
-r, --reverse instead of showing logical ops, show physical
-t, --timing use timing mode, instead of mapping mode
-c, --compute compute answers for me
The -C flag allows you to set the chunk size of the RAID, instead of using the
default size of one 4-KB block per chunk. The size of each request can be
similarly adjusted with the -S flag. The default workload accesses random
blocks; use -W sequential to explore the behavior of sequential accesses. With
RAID-5, two different layout schemes are available, left-symmetric and
left-asymmetric; use -5 LS or -5 LA to try those out with RAID-5 (-L 5).
Finally, in timing mode (-t), the simulator uses an incredibly simple disk
model to estimate how long a set of requests takes, instead of just focusing
on mappings. In this mode, a random request takes 10 milliseconds, whereas a
sequential request takes 0.1 milliseconds. The disk is assumed to have a tiny
number of blocks per track (100), and a similarly small number of tracks
(100). You can thus use the simulator to estimate RAID performance under some
different workloads.